thermal heat transfer boiler

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages

thermal heat transfer boiler have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.

thermal heat transfer boiler.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
thermal heat transfer boiler thermal heat transfer boiler thermal heat transfer boiler

Organic Heat Transfer Boiler - Made-in-China.c

1983-7-8 · China Organic Heat Transfer Boiler manufacturers - Select 2019 high quality Organic Heat Transfer Boiler products in best price from certified Chinese Boiler manufacturers, Industry Boiler suppliers, wholesalers and factory on > Get A Quote >

Thermal Design of Heat Exchangers - Energiteknik K

2003-10-30 · Thermal Design of Heat Exchangers Sebastian Teir, Anne Jokivuori Heat transfer coefficients of liquids are much higher than those of gases, as can be seen in the comparison presented in table 2. 2 boiler. The furnace heat balance can be specified similarly: > Get A Quote >


The calculation of heat transfer coefficient for platen heating surface in combuster of circuilating fluidized bed (CFB) boiler has great influence upon the design and operation of > Get A Quote >

Theory and Calculation of Heat Transfer in Furnace

Theory and Calculation of Heat Transfer in Furnaces covers the heat transfer process in furnaces, how it is related to energy exchange, the characteristics of efficiency, and the cleaning of combustion, providing readers with a comprehensive understanding of the simultaneous physical and chemical processes that occur in boiler combustion, flow > Get A Quote >

Boiler Efficiency - Engineering ToolB

2019-9-6 · Boiler efficiency may be indicated by. Combustion Efficiency - indicates a burners ability to burn fuel measured by unburned fuel and excess air in the exhaust; Thermal Efficiency - indicates the heat exchangers effectiveness to transfer heat from the combustion process to the water or steam in the boiler, exclusive radiation and convection losses; Fuel to Fluid Efficiency - indicates the > Get A Quote >

Heat Transfer Boiler, Heat Transfer Boiler Suppliers offers 1,108 heat transfer boiler products. About 36% of these are boilers, 12% are heat exchanger, and 1% are other refrigeration & heat exchange equipment. A wide variety of heat transfer boiler options are available to you, such as natural circulation, once through. > Get A Quote >

HTP - Water and Space Heating - Heat Transfer

HTP's space heating boilers provide ultimate comfort and the best overall efficiency ratings while keeping maintenance and operating costs to a minimum. With a HTP high efficiency boiler you can achieve the heat your family or business needs while also saving money and energy. > Get A Quote >

Safety in design of thermal fluid heat transfer syste

2017-10-17 · The design and operation of thermal fluid based heat transfer systems (hot oil systems) is often poorly understood and hence preventable accidents occur due to system failure. This paper loop is such that it also prevents the boiler draining back in the event of a leak on the liquid return line. > Get A Quote >

4.1MW Chain Grate Coal Fired Thermal Oil Heaters

Thermal oil boilers, a special oil-based thermal fluid are used as the heat carrier – instead of water or steam. This thermal fluid-also called heat transfer fluid – operates at atmospheric pressure all the way up to 300℃. Thermal oil offers the user high temperature at very low pressures. > Get A Quote >

thermal heat transfer boiler -

thermal balance of the heat transfer boiler – Alibaba . Bell & Gossett ESP-Thermal Heat Exchanger … ESP-Thermal is an on-line plate heat exchanger selection program for Consulting Engineers and Design/Build Contractors.Thermodynamics – WikipediaThermodynamics is a branch of physics concerned with heat and temperature and their relation to other forms of energy and work.The … > Get A Quote >

Clean Boiler Water-side Heat Transfer Surfac

2017-5-3 · Clean Boiler Water-side Heat Transfer Surfaces Even on small boilers, the prevention of scale formation can produce substantial energy savings. Scale deposits occur when calcium, magnesium, and silica, commonly found in most water supplies, react to form a continuous layer of material on the waterside of the boiler heat exchange tubes. > Get A Quote >