boiler superheater acid cleaning

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

boiler superheater acid cleaning have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


boiler superheater acid cleaning.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
boiler superheater acid cleaning boiler superheater acid cleaning boiler superheater acid cleaning

Boiler Cleaning Methods & Techniques - Power

2014-4-14 · Keeping a power plant's boiler clean is an important part of increasing efficiency and avoiding forced outages. Power Engineering looks at different methods and practices for cleaning boilers.

lexie@zozen.com > Get A Quote >

List of Boiler Accessories Thermodynami

2019-9-9 · A smooth tube hairpin type superheater which is used in a Lancashire boiler is shown in fig. 5-13, which also gives the position of the superheater in the boiler. The superheater is placed in the downtake of the boiler and it receives heat from the hot gases passing through the downtake. The superheater consists of two headers.

lexie@zozen.com > Get A Quote >

Chemical Cleaning Of Boilers - To Clean or Not To Cle

2019-9-14 · Chemical Cleaning Of Boilers - To Clean or Not To Clean Removing Deposits. Chemical cleaning has been considered a necessary part of boiler maintenance for many years. The objective of a chemical cleaning is to safely remove all the deposits from the inside of the boiler tubes.

lexie@zozen.com > Get A Quote >

Boiler chemical cleaning_ - SlideSha

then start steem booling befor boiler chemical cleaning . Alkali Cleaning Hot Water Flushing Alkali Boil-out Cold Water Rinsing • Acid Cleaning HCl Cleaning DM Water Rinsing Citric Acid Rinsing DM Water Rinsing Neutralization Passivation (1st and 2nd Stage) • Inspection Bharat Heavy Electricals Limited 33 Power Sector: Technical

lexie@zozen.com > Get A Quote >

Boiler Chemical Cleaning- Valmet Approa

2016-3-23 · Cleaning Procedure Executed A Collaborative Effort Between Valmet, Operations and the Chemical Cleaning Vendor Flows, Temperatures, and Levels Routinely Monitored by Operators, Valmet, and Chemical Cleaning Vendor Boiler Walked Routinely for Leak Detection Chemical Cleaning Vendor Operates Temporary Equipment, Handles

lexie@zozen.com > Get A Quote >

Boiler Cleaning Methods & Techniques - Power

2014-4-14 · Keeping a power plant's boiler clean is an important part of increasing efficiency and avoiding forced outages. Power Engineering looks at different methods and practices for cleaning boilers.

lexie@zozen.com > Get A Quote >

Exfoliation Corrosion - Chemical Boiler S.

Chemical Boiler S.L. > Commissioning > Exfoliation Corrosion. During Inspection. Severe leakages in a steam generator superheater were the leading cause of a major outage a few months after first operation of a power plant. Failure investigation was conducted to reveal that unsatisfactory chemical cleaning left a heterogeneous layer of

lexie@zozen.com > Get A Quote >

CN102337169B - Multicomponent slag-removing and as

2010-7-16 · The present invention relates to a suitable power, petrochemical, coal sizes thermoelectric dry bottom boiler decoking, scorch and cleaning auxiliaries. One

lexie@zozen.com > Get A Quote >

Tube cleaning on superheater - Boiler and Pressure

2002-5-8 · We are replacing a superheater on a sulphuric acid plant. Downstream of the superheater is a 4MW steam turbine. Steam purging is very expensive in an operating plant, and we are considering using chemical cleaning of the tubes post construction.

lexie@zozen.com > Get A Quote >

RECOVERY BOILER WATER TREATMENT Figure 2 - tappi.o

2008-1-4 · chemical cleaning of boilers. superheater lost on this boiler in 6 months after a boiler water chemistry change from sodium phosphates to potas-sium phosphates. Plant personnel had not realized the link of salts to their acid form. Values should be low (e.g., <0.2-0.5 µS/cm) except in …

lexie@zozen.com > Get A Quote >

Finding the Root Cause of Boiler Tube Failures -

The damage results from cracks that propagate from the ID. The source of corrosive fluid may be carryover into the superheater from the steam drum or from contamination during boiler acid cleaning if the superheater is not properly protected. Components typically affected: Stainless steel superheater …

lexie@zozen.com > Get A Quote >