steam boiler power plant

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

steam boiler power plant have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


steam boiler power plant.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
steam boiler power plant steam boiler power plant steam boiler power plant

Power Plant Boiler, Power Plant Boiler Suppliers an

Alibaba.com offers 6,871 power plant boiler products. About 46% of these are boilers, 13% are boiler parts, and 1% are energy saving equipment. A wide variety of power plant boiler options are available to you, such as power station, industrial.

lexie@zozen.com > Get A Quote >

Power Plant Gas Turbine Steam Turbine Boiler

2018-12-20 · Vasavi Power. VPSPL offer a full range of services across the entire life-cycle of your plant under one roof. Our service portfolio ranges from engineering, construction, operation, maintenance to plant …

lexie@zozen.com > Get A Quote >

Power Plant and Boiler Models for Operator Trainin

E.g., the extended Luenberger's state controller-observer of superheated steam temperature was developed for coal pulverized steam boiler of Power Plant Shen Tou 500 MW, in District Shan Si, China (Neuman, et al., 1988). 5.

lexie@zozen.com > Get A Quote >

Steam Power Plant Construction,Working, Advantages

In this article we will study about the construction,working, efficiency, advantages and disadvantages of steam power plant. Steam Power Plant. It is the power plant which is used to generate electricity by the use steam turbine. The major components of this power plant are boiler, steam turbine, condenser and water feed pump.

lexie@zozen.com > Get A Quote >

How to calculate boiler efficiency by Direct Metho

2019-8-23 · How to calculate boiler efficiency by Direct Method ? in this article we discussed about the boiler efficiency how it calculated by direct and indirect method what are the factor responsible for the boiler efficiency . advantage or d isadvantages of direct and indirect method for calculating boiler …

lexie@zozen.com > Get A Quote >

What's the working principle of power plant boil

2019-4-26 · What's the working principle of power plant boiler 2017-07-19 17:09:09. A power boiler is the primary source of steam in most utility and industrial facilities. Its purpose is to create steam by combusting fuels to generate heat and transferring that heat energy to water. Steam is the primary form of power generation in most of the world

lexie@zozen.com > Get A Quote >

Basics of Steam Generation - Energiteknik K

2003-10-30 · The Basics of Steam Generation - 6 expansion is the source of power in all steam engines. It also makes the boiler a dangerous device that must be carefully treated. The theoretical amount of heat that can be transferred from the combustion process to the working fluid in a boiler is equivalent to the change in its total heat content from

lexie@zozen.com > Get A Quote >

Boiler In Thermal Power Plant - coalhandlingplants.c

Boiler In thermal power plant accumulates the steam and build up a pressure to expend it in turbine and convert thermal energy to mechanical energy. Boiler In thermal power plant accumulates the steam and build up a pressure to expend it in turbine and convert thermal energy to mechanical energy.

lexie@zozen.com > Get A Quote >

What is the temperature of a boiler in a power plant?

Temperature inside boiler (furnace) is around 1100 deg to 1200 deg. Although it is favorable to keep it under 1100 deg or otherwise ash in flue gas will melt as forming clinkers and it will stick to to boiler walls. I am talking about big boilers

lexie@zozen.com > Get A Quote >

UNIT 2 STEAM POWER PLANT Steam Power Plant - IGN

2011-3-28 · UNIT 2 STEAM POWER PLANT Steam Power Plant Structure 2.1 Introduction Objectives 2.2 Basic Consideration in the Analysis of Power Cycles 2.3 Steam Generator 2.4 Super Heater 2.5 Feed Water Heater 2.6 Furnaces 2.7 Energy Performance Assessment of Boilers 2.8 Steam Turbines Steam Boiler

lexie@zozen.com > Get A Quote >

Thermal power station - Wikiped

2019-9-14 · A thermal power station is a power station in which heat energy is converted to electric power.In most of the places in the world the turbine is steam-driven.Water is heated, turns into steam and spins a steam turbine which drives an electrical generator.After it passes through the turbine, the steam is condensed in a condenser and recycled to where it was heated; this is known as a Rankine cycle.

lexie@zozen.com > Get A Quote >