boiler flue temperature

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages

boiler flue temperature have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.

boiler flue temperature.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
boiler flue temperature boiler flue temperature boiler flue temperature

FLUE GAS RECIRCULATION - combustionexperts.c

2008-7-10 · temperature base control scheme. The temperatures required for automatic operation are ambient air, flue gas temperature at the FGR fan and the temperature of the mixture of flue gas and air. With these temperatures the %FGR can be calculated and a curve can be programmed to maintain a boiler load versus %FGR curve. > Get A Quote >

Consider Installing a Condensing Economiz

2014-5-20 · A conventional feedwater economizer reduces steam boiler fuel requirements by transferring heat from the flue gas to the boiler feedwater. For natural gas-fired boilers, the lowest temperature to which flue gas can be cooled is about 250°F to prevent condensation and … > Get A Quote >

flue-gas temperature deviatio

Research on The Forming Mechanism of The Flue-Gas Temperature Deviation in The Horizontal Pass for Tangentially Fired Boiler > Get A Quote >

Low Temperature Corrosion in Boiler and Its Preventi

The amount of SO 3 produced in boiler flue gas increases with an increase of excess air, gas temperature, residence time available, the amount of catalysts like vanadium pentoxide, nickel, ferric oxide, etc., and the sulphur level in fuel. > Get A Quote >

Flue Temperature - an overview ScienceDirect Topi

The flue temperature plays an important role because an increase in the mean flue temperature (MFT) over a range between 1165 and 1390 °C –to produce carbonization rates of 20, 25, and 30 mm/h, respectively-, significantly modifies the yield, properties, and composition of the by-products. A higher amount of COG is generated with a lower > Get A Quote >

boiler flue gas temperature calculation Industrial Ga

Flue Gas Temperature and Heat in the Flue Gas Flow (Btu … Flue Gas Temperature and Heat in the Flue Gas Flow (Btu/hour) [ back to full computer program list] This computer program calculates the specific heat (Btu/lb-F) and the enthalpy (Btu/lb) for typical gases … > Get A Quote >

Product flue gas temperature in boil

flue gas temperature in boiler. With more than 30 years of manufacturing boilers, the company has formed more than 400 varieties of gas boilers, biomass boilers, coal … > Get A Quote >

boiler flue gas temperature calculation Industrial Ga

Flue Gas Temperature and Heat in the Flue Gas Flow (Btu … Flue Gas Temperature and Heat in the Flue Gas Flow (Btu/hour) [ back to full computer program list] This computer program calculates the specific heat (Btu/lb-F) and the enthalpy (Btu/lb) for typical gases found in the flue … > Get A Quote >

Flued boiler - Wikiped

2019-9-7 · The simplest form of flued boiler was Richard Trevithick's "high-pressure" Cornish boiler, first installed at Dolcoath mine in 1812. This is a long horizontal cylinder with a single large flue containing the fire. As the furnace relied on natural draught, a tall chimney was required at the far end of the flue to encourage a good supply of air (oxygen) to the fire. > Get A Quote >

Flue Gas Temperature Sensor - Viessma

2019-9-12 · Flue Gas Temperature Switch Installation For more details refer to the Installation and Service Instructions applicable to this boiler. Note: The flue gas temperature sensor is located on the flue gas collector. 1. Remove the screws, the cable strap and connector cover from the flue … > Get A Quote >

Flue Gas Boiler - Waste Heat Boiler - Zhong Ding

Flue Gas boilers are the significant energy saving equipment, utilize the heat in flue gas from combustion processes or hot extract air from industrial processes to generate hot water or saturated steam Otherwise, the flue gas boiler could be used in oil gas fired combined cycle units, and take advantage of the high temperature flue gas heat discharged by gas turbine > Get A Quote >