boiler types for selection

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

boiler types for selection have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


boiler types for selection.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
boiler types for selection boiler types for selection boiler types for selection

Boiler feed pump K

Boiler feed pumps are also referred to as feed pumps (see Reactor pump) and designed as multistage radial flow pumps. (Also see Multistage pump.). They serve to feed a steam generator such as a boiler or a nuclear reactor with a quantity of feed water corresponding to the quantity of steam emitted.

lexie@zozen.com > Get A Quote >

An Engineering Guide to Modern Fuel Syste

2016-12-1 · Boiler Systems Pump Selection Typical modern boilers will fire natural gas as the primary fuel, with a percentage of these using #2 fuel oil as a backup fuel. A system designer should be aware of a couple of key points when in-volved with boiler fuel oil systems. 1) Most boilers firing fuel oil will have their own fuel oil pump.

lexie@zozen.com > Get A Quote >

Requirements for Boiler and Pressure Vessel Manufactur

2010-1-11 · and pressure vessel manufacture licensing, quality management system requirements and boiler and pressure vessel safety quality requirements. The resource requirements include basic requirements and specific requirements. The basic requirements are the general requirements for producing all kinds of boiler and pressure vessel products

lexie@zozen.com > Get A Quote >

Reboiler Exchanger and System Type Selection – What

The purpose here is not to go into design details of each specific type but rather to examine the selection criteria that favor one configuration over another. Since shell-and-tubes are so common, most of the discussion focuses on them but some factors favoring other designs are covered as well. Many factors influence reboiler type selection.

lexie@zozen.com > Get A Quote >

what are Boiler Types - AONG websi

The current design objective is to provide low-cost energy with an acceptable impact on the environment. As discussed in an engineering manual published by ABMA, control of PM, NOx, CO, and SO2 emissions is now a significant consideration in the overall boiler and combustion equipment design and selection process. TYPES OF ICI BOILERS

lexie@zozen.com > Get A Quote >

boiler types for selection - Professional boiler

Boiler-selectionpdf:selectionpdf Boiler Selection Considerations Section I1-406-08 BOILER TYPES boilersdiscussed packagedboilers. concepthas been around morethan 60 years Ask PriceEmail UsBOILER SELECTION CONSIDERATIONS Cleaver-Brooks Boiler Selection Considerations 3 BOILER TYPES The boilers discussed in this book

lexie@zozen.com > Get A Quote >

What is a Boiler? Classification of Boiler, Selectio

2019-9-3 · What is a Boiler? Boiler Mountings & Accessories: In this article, I will explain about What is a Boiler?Selection of a boiler, Essentials of Good boiler, Classification of a boiler, Diagram of the boiler, Boiler Mountings and Boiler Accessories in a detailed way.

lexie@zozen.com > Get A Quote >

Boiler Selection - BOILER SELECTION

View Boiler Selection from UNKNOWN xx at International Academy of Design & Technology. BOILER SELECTION CONSIDERATIONS CONTENTS Definitions

lexie@zozen.com > Get A Quote >

BOILER SELECTION CONSIDERATIONS - manoxblog.c

Boiler Selection Considerations. Perhaps no other piece of equipment is more important to a facility than the boiler. Proper boiler selection, to meet the needs of the application, is a critical factor in the design of any steam or hot water system. This section provides information to consider when selecting a boiler.

lexie@zozen.com > Get A Quote >

Boilers (industrial) Selection Guide Engineering3

There are many different types of industrial boilers available. Selecting between these types can be simplified by looking at three separate aspects of boilers: function, technology, and heat source. Function. The most fundamental decision when selecting a boiler is what its function will be.

lexie@zozen.com > Get A Quote >

(PDF) A Rule-Based Industrial Boiler Selection Syst

A Rule-Based Industrial Boiler Selection System. View the table of contents for this issue, or go to the journal homepage for more There are various types of boiler with different

lexie@zozen.com > Get A Quote >