parameter of thermal power plant boiler

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages

parameter of thermal power plant boiler have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.

parameter of thermal power plant boiler.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
parameter of thermal power plant boiler parameter of thermal power plant boiler parameter of thermal power plant boiler

Required Parameter For Design Of Boiler Superheat

Steam Boiler Working principle and Types of Boiler . 2019-8-16 · Boiler or more specifically steam boiler is an essential part of thermal power plant. Definition of BoilerSteam boiler or simply a boiler is basically a closed vessel into which water is heated until the water is converted into steam at required pressure. > Get A Quote >



A Nonlinear Lumped-Parameter Dynamic Model of

Traditional models of power plant boiler superheater are incapable of simulating the operating conditions under large disturbances with high precision. To resolve this challenging problem, this paper presents a nonlinear lumped-parameter dynamic model of power plant boiler superheater. The present model describes the dynamic processes of the pressure-flowrate and the enthalpy-temperature > Get A Quote >

The top 10 biggest thermal power plants in Ind

The Tiroda thermal power plant is a 3,300MW coal-based power generation plant in Maharashtra, India. Owned and operated by Adani Power Maharashtra, the power plant consists of five 660MW units. The first unit of the power plant was commissioned in August 2012, while the last unit commenced operations in October 2014. > Get A Quote >

CFB biomass boiler,CFB Biomass fired power plant

2019-8-20 · CFB Power Plant Boiler is a kind of large scale heating equipment applied in thermal power plant and other industries for power generation, it has the features of fuel flexibility, high combustion efficiency, low NOx, SOx emission, it is the good clean heating or power solution. > Get A Quote >

boiler light up procedure thermal power plant – CFB

2017-9-6 · 3.How about the quality of boiler light up procedure thermal power plant ? Our industrial steam boiler manufactured strictly according to national and international standard. our products have approved ASME, IBR, ISO9001-2008, etc. boiler light up procedure thermal power plant Customer visiting > Get A Quote >

Minhang Power Plant, Shanghai Electric Power Co., Lt

2019-6-28 · The #8 boiler in the Minhang Power Plant, Shanghai Electric Power Co., Ltd., is a G400/150-50408 supercritical reheat boiler produced by Shanghai Boiler Works. The boiler has full open-air configuration, equipped with the steam turbo generator unit with 135.1 MW rated power. The boiler was suspended and converted into a coal boiler in June 1982. > Get A Quote >

Dynamic simulation model for ultra supercritical 1 000M

XU Hui 1,XU Ershu2 1.College of Control and Computer,North China Electric Power University,Baoding 071003,Hebei Province,China 2.Key Laboratory of Condition Monitoring > Get A Quote >

boiler drum in thermal power plant – Boiler Catalog

2017-10-26 · Images for boiler drum in thermal power plant Quick inquiry Email Us; Thermal power station – Wikipedia, the free encyclopedia. A thermal power station is a power plant in which heat energy is converted to electric power. > Get A Quote >

Parametric identification of integrated model of a coa

2019-9-12 · The primary objective of this article is to identify model parameters of a coal-fired integrated boiler and to present a comparative study on three different identification methods. This leads to select most suitable models that are applied for the developed model of the boiler of 210 MW coal-fired thermal power … > Get A Quote >

A New Approach Applied to a Thermal Power Plant

2009-12-5 · which are the most important control loops of power plant, have been implemented using PLC's. 2 A Thermal Power Plant Unit Most thermal power plants generate a power ranged from 125 MW to 1000 MW power. They generally consist of three main elements which are boiler, turbine, and alternator, and other complementary > Get A Quote >